2025 Super MB Pro M6+ PRO Full Package for Doip Benz Diagnostic Tool Support BMW Aicoder E-SYS and Immercode, Bimmerlink APP

M6+ PRO Mercedes-Benz and BMW configuration
 
1. Plug the M6+PRO into the power supply or connect the OBD to the test vehicle, and plug in the USB/LAN cable of the M6+PRO.
2. Turn on the computer and plug in the computer USB/LAN cable.
3. Open the computer network configuration interface and find the Realtek USB FE Family Controller network/the network adapter that comes with the PC.


4. Click “Properties”--TCP/IPV4, and set the IP address as shown in the figure below.


5. Click “Advanced”, and add a group of network IP addresses as shown in the figure below.



6. Click “OK”. After the configuration is successful, the display is as follows.



7.For the same computer, if you replace a new M6+PRO, you need to reset the IP address. After the setting is completed, the computer is successfully bound to the M6+PRO and there is no need to set the IP address again for wired and wireless Internet access. (Use LAN port connection mode, no need to re-set IP when changing devices).
 
8.You can test Mercedes-Benz normally. Please connect the diagnostic cable with SUPER MB PRO logo.

9. BMW wireless BMWAiCode configuration(only for F+G chassis)
Connect to the M6+PRO -***, password：123456789, wirelessly, press and hold the M6+PRO switch button for 3 seconds, and the M6+PRO host wireless indicator will flash. The computer-side BMWAiCoder configuration is as follows:

10. BMW wired BMWAiCode configuration(only for F+G chassis)
Connect the USB/LAN cable, press and hold the M6+PRO switch button for 3S, and the M6+PRO host wired indicator light will flash. The computer-side BMWAiCoder configuration is as follows:


11. BMW wired and wireless E-Sys configuration(only for F+G chassis)
Connect to the M6+PRO -*** wirelessly, press and hold the M6+PRO switch button for 3 seconds, and the M6+PRO host wireless indicator will flash. On the computer side, select the following for direct connection. Wired is similar, no setup required.

12. BMW wired ISTA configuration(only for F+G chassis)
  Connect the USB cable, press and hold the M6+PRO switch button for 3S, and the M6+PRO host wired indicator light will flash. The computer ISTA configuration is as follows:


13. BMW Wireless ISTA configuration(only for F+G chassis)
  Connect to the M6+PRO -*** wirelessly, press and hold the M6+PRO switch button for 3 seconds, and the M6+PRO host wireless indicator will flash. The computer side is selected as follows:


14.The mobile phone BWM APP adopts wireless connection. (only for F+G chassis)
Connect to the M6+PRO -***, password: 123456789, press and hold the M6+PRO switch button for 3 seconds, and the M6+PRO host wireless indicator will flash.
 
15. Supported BMW models and years.
 

Model Year	2019	2018	2017	2016	2015	2014	2013	2012	2011	2010	2009
X1	√	√	√	√
X3	√	√	√	√	√	√	√	×
X4	√	√	√	√	√	√
X5	√	√	√	√	√	√	×
X6	√	√	√	√	√	×
1 Series	√	√	√	√	√	√	√	√	×
2 Series	√	√	√	√	√	√	√	√
3 Series	√	√	√	√	√	√	√	×
4 Series	√	√	√	√	√	√	√
5 Series	√	√	√	√	√	√	√	√	√	√	×
6 Series	√	√	√	√	√	√	√	√	×
7 Series	√	√	√	√	√	√	√	√	√	√	√

Product Accessories Comparison Chart
 

SUPER MB PRO M6+PRO FULL	1pc x SUPER MB PRO M6+ Pro Host 1pc x OBD2 16pin Cable 1pc x USB Cable 1pc x 38PIN Cable 1pc x 14PIN Cable 1pc x 4PIN Cable
SUPER MB PRO M6+PRO OBD	1pc x SUPER MB PRO M6+ Pro Host 1pc x OBD2 16pin Cable 1pc x USB cable
SUPER MB PRO M6+PRO Truck	1pc x SUPER MB PRO M6+ Pro Host 1pc x OBD2 16pin Cable 1pc x USB cable 1pc x 14PIN Cable

1pc x SUPER MB PRO M6+ Pro Host

1pc x OBD2 16pin Cable 

1pc x USB Cable

1pc x 38PIN Cable

1pc x 14PIN Cable

1pc x 4PIN Cable